Für Profis und Einsteiger
Symetrix 80-0048-B - EDGE Frame Without cards
Dante in Our DNA
Edge DSPs are equipped with 128 (64×64) redundant Dante channels. The Dante protocol enables ultra-reliable multi-channel audio networking over IP. Together, Symetrix and Dante provide the fastest possible way to implement, control, and maintain a system of networked DSPs and accessories – including third party Dante-enabled microphones, loudspeakers, power amps, and mixing consoles.
Total Input/Output Flexibility
Four versatile option card slots enable unique I/O configurations – aligning the hardware with exact system requirements. Optional cards support analog and AES-3 digital I/O as well as special purpose interfaces including AEC, VoIP, and analog telephone.
On-board 10/100 and Gigabit Switches
Unique to Symetrix Radius and Edge DSPs, built in switches lower system cost, reduce or eliminate the need for peripheral switches, and increase system reliability.
Unlimited Programming Flexibility
Edge is programmed using Composer – Symetrix’ award winning open-architecture CAD application. Unique to Composer is the ability to natively configure Symetrix and select third party Dante hardware – thereby eliminating the confusion of multiple or redundant software applications. Learn more about Composer here.
Control Made Easy
Multiple control options include low-cost Symetrix ARC wall panels and an easy to generate SymVue Windows virtual GUI. The human readable Composer Control Protocol supports programming of third-party touch screens and control devices.
An Embedded Web Server for Status and Even More Control. Edge’s embedded web server displays I/O levels, diagnostics data, and hosts ARC-WEB – a browser-based interface for smart phones, tablets, and computers.
Features
- A Powerful DSP Featuring Flexible I/O Configuration
- 128 Channel (64×64) Redundant Dante
- On-board Ethernet and Dante Network Switches
- 4 I/O Expansion Card Slots
|
Specifications |
|
General |
|
|
Processors |
1 x Analog Devices SHARC 21489 @ 400 MHz SIMD |
|
Raw processing capacity |
400 MIPS, 1.6 GFLOPS |
|
Sampling Rate |
48 kHz, ± 100 ppm |
|
Frequency Response (A/D/A) |
20 Hz – 20 kHz, ± 0.5 dB |
|
Dynamic Range (A/D/A) |
> 114 dB, A-weighted |
|
Channel Separation (A/D/A) |
> 108 dB @ 1 kHz, +24 dBu |
|
Latency (A/D/A) |
0.88 mS, inputs routed to outputs |
|
Delay memory |
174 mono seconds per Edge frame |
|
Analog control inputs |
0-3.3 VDC |
|
Recommended external control potentiometer |
10k Ohm, linear |
|
Logic outputs |
Low (0V) when active, pulled high (5V) when inactive |
|
Logic output maximum external power supply voltage |
24 VDC |
|
Logic output maximum external power supply current sinking |
50 mA |
|
Logic output maximum output current |
10 mA |
|
RS-232 accessory serial I/O |
38.4 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required |
|
RS-485 serial I/O |
38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port |
|
Ethernet Cable |
Standard CAT5, maximum device to device length = 100 meters |
|
Dante Cable |
Standard CAT6, maximum device to device length = 100 meters |
|
ARC Cable |
Standard CAT5, distance dependent upon load and number of devices |
|
Maximum devices per system |
32 units per Site File |
|
Maximum stored presets |
1000 |
|
Mechanical Data |
|
|
Space Required |
1U (WDH: 18.91 in x 9.5 in x 1.72 in / 48.02 cm x 24.13 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections |
|
Electrical |
100-240 VAC, 50/60 Hz, 45 Watts maximum universal input and/or suitable 24 VDC / 2.0 Amp auxillary power source. No line voltage switching required |
|
Ventilation |
Maximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in. minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc |
|
Certifications or Compliance |
UL 60065, cUL 60065, IEC 60065, EN 55103-1, EN 55103-2, FCC Part 15, RoHS |
-
Hilfe,
- GE : + 41 22 561 07 07
- ZH : + 41 43 255 59 00
- TI : + 41 91 985 25 11
Finanzierung,
Rufen Sie uns an!
