Filter
Contrik AG is one of the leading Swiss suppliers of high-quality cables, connectors and instruments tailored to all requirements in the entire entertainment industry. Our challenge is to provide versatile and high-quality solutions.
152.4m Techflex FlexoPET, diameter 9.5-25.4mm, black
152.4m Techflex FlexoPET, dimeter 9.5-25.4mm, grey
152.4m Techflex FlexoPET, diameter 9.5-25.4mm, white
The FP-TPSR4A Format-A Two-Pair Audio Sender/Receiver provides the interface between a hotel room television and listening stations and audio input panels. The Sender Section is an RDL Format-A audio sender that accepts either a stereo line-level or 1 to 3W mono amplified fixed-level signal, usually from a commercial hospitality equipped TV.
Standard Circular Connector POSITIONER MINICON MPC MALE CRIMP W/ HX
70m 0.8L/3.7 Flex 6GHz, KTGT310, 2xBNC
Crimp tool die for HX-BNC. Pin crimping: 1.6 mm. Shield and jacket: HEX crimp 6.47 mm (A), 5.00 mm (B)
Techflex CleanCut, diameter 6.4-19.1mm, black, 152.4m
Techflex CleanCut, diameter 6.4-19.1mm, gray, 152.4m
The RU-SC2 is the ideal choice in installations when two RS-232 devices requiring full-duplex communication are to be connected at a long distance. Connection to the RS-232 device is made on the front panel. The RS-422 input and output connections and power connections are made on the rear panel through full-size, clearly identified, barrier block terminals.
The FP-PA18 is a high efficiency 18 W power amplifier with a line input, 8 ohm output, integral audio compressor and an automatic sleep mode. The FP-PA18 features a balanced line level input that may be connected unbalanced. A gain control located next to the terminal block is designed to be adjusted manually or with a trimming screwdriver.
Speakercab. 2x1.5mm2, Cca s1a-d0-a1 100m
40m Armored AOC HDMI 2.0 4K Cable UF
30m U-Flex Armored HDMI 2.1 8K@60HZ
50m Black, flexible Etherflex Cat.5e patch cable (ZNK CT2672601) for applications in demanding environments. Twisted pair, UC300 HS26 4P, SF/UTP, 4 x 2 x ASW 26, with copper litz wire, with PUR jacket, assembled with shielded RJ45 Hirose connectors (NE8CAT6A-HRS) and Neutrik etherCON cable connector housings with bushings. The cable is supplied on cable...
FF EBC15 foxBRID Chassis coup 4CH MM OM4
Table connection box made of anodised aluminium (natural), with 6x FLF cut-outs (or 3x twin FLF cut-outs), rear cable inlet, brush and clamps which are adjustable up to a table thickness of 40 mm. Dimensions (without clamps): 338 x 134 x 85 mm.
The EZ-MPA2 is a stereo microphone preamplifier with front-panel volume controls and audio level metering. A front-panel switch engages audio compressors to control overloads and clipping during high level audio bursts or peaks from the microphones. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. Includes...
Techflex Flexo F6, diameter 25.4mm, black, 30m
Techflex F6 Woven, diameter 19.1mm, white, 45.7m
Power Rack CPR32-C2-F9-CB
Techflex CleanCut , diameter 3.2-6.4mm, gray, 304.9m
Techflex CleanCut diameter, 3.2-6.4mm, black, 304.9m
Techflex Flexo Wrap, diameter 19.1mm, beige, 30.5m
Techflex Flexo Wrap, diameter 19.1mm, grey, 30.5m
Techflex Flexo Wrap, diameter 19.1mm, white, 30.5m
Techflex Flexo Wrap, diameter 19.1mm, black, 30.5m
Techflex F6 Woven, diameter 44.5mm, black, 15.2m
The FP-PA18H is a high efficiency 18 W power amplifier with a line input, 8 ohm output and audio compressor capable of operation in a high ambient temperature environment. The thermal characteristics of the module case and construction throughout using high temperature components permit operation over a range of 0 to 70 degrees C.
Crimp tool die for HX-BNC. Pin crimping: 1.6 mm. Shield and jacket: HEX crimp 7.36 mm (A)
30m U-Flex Slim Armored HDMI 2.1 8K@60HZ
The RDL Active Loudspeaker Format-A Series features a white grill and is designed to deliver rich, detailed sound while in Decora-style compatible wall or chassis mounts. The loudspeaker is a single-pair audio amplifier module compatible with RDL Format-A twisted pair products.
30m Cat.6AU/FTP ECON Armor UFlex GT235
The RU-EQ3 is a three band, shelving single channel EQ and features a balanced bridging input, which may be connected unbalanced if desired. The output driver is 150 Ohm balanced, and is intended to drive unbalanced or balanced lines of 150 Ohm or higher impedance.
The D-TPR3A Active Triple Pair XLR and RCA Stereo Audio Output over RJ45 Receiver Module is a three-pair audio receiving module compatible with RDL Format-A twisted pair products. The D-TPR3A features a white front-panel laminate with gray lettering that matches RDL Decora-style remote controls.
The EZ-HDA6 contains six stereo headphone amplifiers with individual front-panel volume controls. Headphone outputs are provided on rear-panel 1/4" jacks. One input signal feeds all the amplifiers. Stereo RCA jacks, a MINI jack and a dual 1/4" jack (for "loop out" connection) are provided for connecting the input source. Includes worldwide power supply...
The FP-UBC2 2-Channel Unbalanced to Balanced Converter is the ideal choice for connectorized conversion from unbalanced to balanced audio. This module features two identical channels. Gold-plated phono jacks are used for each unbalanced input channel; each balanced channel is connected through an XLR jack.
Speaker cable ZNK 8/14 (8x2.5 mm2) black. Assembled with NL8FC on both sides.
The black 19 inch panel wall box with 5RU and a depth of 127 mm is ideal for the mounting of different panels. The lateral cut-out makes cable feeding convenient and easy. An internal ground terminal permits an appropriate grounding concept. Dimensions: 482.6 x 127 x 291 mm
Techflex F6 Woven, diameter 50.8mm, black, 12.2m
The FP-BUC2 is the ideal choice for connectorized conversion from balanced to unbalanced audio. This module features two identical active (transformerless) channels. Gold contact XLR jacks are utilized for the balanced input channels. Each output is unbalanced, connected through a gold-plated phono jack. A level trim potentiometer is provided for each...
2/1 Shrinkfl. U-Clear, Diameter 19.1mm Bulk 76.2m
60m 0.8L/3.7 Flex 6GHz, KTGT310, 2xBNC
30m U-Flex Armored HDMI 2.1 8K@60HZ
Techflex Flexo F6, diameter 38.1mm, white, 15m
Techflex Flexo F6, diameter 38.1mm, gray, 15m
30 m Armored AOC HDMI 2.0 Cable 2Cap
The STM-LDA3 is designed for use in quality commercial sound, broadcast and recording applications. The 1.2 kilohm balanced input accepts a wide variety of microphone input levels without loading professional low-impedance microphones. A multi-turn gain trimmer allows precise output level adjustment. The output signal is available on three separate...
30m Cat.6AU/FTP RJ45 Armor UFlex GT235
The FP-TP4PW 4 Output Power Inserter is a four output power inserter compatible with RDL twisted pair products. The RU-TP4PW is powered from a 24 VDC power supply using either the power jack or the detachable terminal block. Four dual-RJ45 jack sets are provided to connect remote twisted pair senders and receivers. Power is provided to all modules...
1.4HDMI-HDBT ExtenTX/RXSet-70M,BidiPower
The two-channel pass-through adapter FIBERFOX 2CH Bridge is based on the contact-free and extremely dirt-resistant "Expanded Beam" lens technology and has LC connections on the back side as a special feature, so that adaptation from the front-side lens plugs to Physical Contact is possible without additional packaging.
FF EBC15 Chassis 2CH MM OM4 LOCKED
Power multicore cable CKPE50-ASAS-M400
The RU-UDA4 is the optimum choice where connectorized, unbalanced line-level distribution is needed. This unit features two separate, isolated channels. The RU-UDA4 may be used in stereo applications, or as two individual monaural distribution amplifiers. The input signals are buffered through output line drivers, providing four separate line-level...
Speaker Cable, Speakonflex, 2 x 2.5 mm2, outer diameter 8 mm, high-flexible, black.
DMX Cable are commonly used as stage control systems in Broadcasting (lighting) or for control of effect processors. DMX stands for "Digital Multiplex". This DMX Light Control Cable (Pat 512, 2 x 2 x 0.32 mm2) is black and therefore well-suited to be installed in theatres or concert halls. The jacket is made of DMC Flex PVC and is braid-and foil shielded.
Black microphone cable on the cable reel KTGT310, assembled with 2x Neutrik convertCON 3-pole XLR cable connectors, (NC3FM-C-B, male to female). The cable ZNK 2/6-BL has a length of 50 m.
Analog Swissflex Premium Microphon cable, 2 x 0.50 mm2 , double spiral shielded, PVC jacket, black, outer diameter 6.8 mm.
Techflex CleanCut, diameter 4.8-15.9mm, gray, 152.4m
Techflex CleanCut, diameter 4.8-15.9mm, black, 152.4m
Techflex Flexo F6, diameter 38.1mm, black, 15m
Techflex CleanCut, diameter 25.4-38.1mm, gray, 76.2m
Techflex CleanCut, diameter 25.4-38.1mm, black, 76.2m
This cable reel is made of sheet steel, has a core diameter of 178 mm and no cover. It is suitable for daily outdoor applications and is equipped with exchangeable, shock-resistant steel panels. An ergonomic fixing brake is integrated in the frame.
Techflex Flexo F6, diameter 31.8mm, white, 15m
30m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
25m U-Flex Slim Armored HDMI 2.1 8K@60HZ
Rugged, balanced microphone cable AES / EBU, 1 pair, 2 x 0.22 mm2, with spiral shield, amplified with Kevlar dummy elements, outer diameter 6.5 mm, with Rugged, balanced microphone cable AES / EBU, 1 pair, 2 x 0.22 mm2, with spiral shield, amplified with Kevlar stranded wires, outer diameter 6.5 mm, with DMC Flex PUR jacket, 110 Ohm.
30m Cat.6A U/FTP ECON/ECON Armor U-Flex
3RU opticalCON panel frame
5GHZ Antenna 14DBI Gain, 40 degrees Horizontal angle, 35 degrees Vertical angle.
The D-TPR2A Active RCA Stereo Audio Output over Dual RJ45 Receiver Module is a CAT5 to RCA phono receiver module. The The D-TPR2A features a white front-panel laminate with gray lettering that matches RDL Decora-style remote controls. The D-TPR2A module features two RCA phono jack outputs, one for the left channel output and one for the right channel.
The EZ-MX4ML is a stereo audio mixer with two mic and two line inputs. Microphones connect through balanced XLR jacks that provide phantom voltage. Both line inputs connect through RCA jacks; one also includes a MINI-jack input. Left and right channel LED VU metering facilitates easy level adjustment. Includes worldwide power supply (specify plug).
Techflex F6 Woven Diameter 6.4mm WT 61m
The STM-3 is a quality low-noise microphone preamplifier designed for use in surveillance, commercial sound, broadcast, and recording where higher than normal gain is required. The STM-3 is very flexible, with gain adjustment from 45 to 75 dB, two balanced or unbalanced outputs, and available phantom supply input.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Tascam standard.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Yamaha standard.
The RDL EZ-HSX4 4 Channel Audio Switcher is a simple device that effectively switches between 4 consumer audio sources. Four RCA stereo inputs accomodate consumer line-level devices, and 1/4" phone and 1/8" (3.5mm) mini headphone outputs are features on the front panel. Includes worldwide power supply (specify plug).
30m Armored AOC HDMI 2.0 4K Cable UF
The STM-2X is the ideal choice in many installations where a microphone preamplifier is required, and is the ideal choice where either a toggle-type switch or push-to-talk switch is to be provided for microphone control, particularly if condenser microphones are used.
ZNKMP8/14 (Multicore cable 11,7 mm 8 x 2 strands of 0,22 mm2 with PVC jacket) Side a: 8 x NC3FXX; Side b: 8 x NC3MXX incl. XXCR and coloured BXX
25m U-Flex Armored HDMI 2.1 8K@60HZ
30m Cat.6A U/FTP ECON/RJ45 Armor U-Flex
The D-TPS3A Triple Pair RJ45 Sender Module is a three-pair audio sending module compatible with RDL Format-A twisted pair products. The D-TPS3A features a white front-panel laminate with gray lettering that matches RDL Decora-style remote controls. This module features an XLR microphone input and two RCA phono jack inputs, one for the left channel source...
The TX-VLA1 is the ideal choice in installations where video signals are being fed into long cables, or where a low video signal needs to be amplified. The unique power supply input allows the TX-VLA1 to be powered from a wide variety of existing ac or dc power sources.
The black DB-TPRX3A 3-Input Format-A Source Selector allows you to select between 3 audio different audio sources, and provides a balanced line-level output via detachable terminal block. Only one source can be selected at a time, and selecting a new source defeats the other sources. An LED indicator shows which of its 3 inputs is selected at any time.
The TX-AVX is the ideal choice in installations where automatic switchover to an alternate video source is needed when the primary signal is lost. The unique power supply input allows the TX-AVX to be powered from a wide variety of existing ac or dc power sources.
2/1 Shrinkfl. U-Clear, Diameter 15.9mm Bulk 76.2m
Flexible Etherflex patchcable (ZNK CT1019067) Cat. 7, twisted pair, PUR-rubber-jacket (resistant, non-abrasive, non-corrosive, flame retardant), assembled with Cat. 6A RJ45 Hirose connectors, screened (NE8CAT6A-HRS) along with standard boots.
Techflex F6 Woven Diameter 4.8mm WT 61m
Techflex F6 Woven, diameter 19.1mm, black, 45.7m
Techflex Flexo Wrap, diameter 12.7mm, white, 30.5m
Techflex Flexo Wrap, diameter 12.7mm, black, 30.5m
Techflex Flexo Wrap, diameter 12.7mm, grey, 30.5m
Techflex Flexo Wrap, diameter 12.7mm, beige, 30.5m
85m 12G / 2 x UHD BNC / Cable CPR: Dca
Fiber optic dry cleaner kit MTP
The EZ-MCP1 is an in-line microphone compressor that produces consistent audio levels despite wide variations (up to 30 dB) from the microphone. It is installed between a dynamic or condenser microphone and a mic-level mixer or amplifier input. Includes worldwide power supply (specify plug).
30m U-Flex Slim Armored HDMI 2.0 4K@60HZ
The STR-19B Stick-On Series Racking System (10 Modules) is a mounting kit designed to accommodate (10) RDL Stick-On modules. It can be mounted in a rack or secured to almost any flat surface. The unit features a series of angled slots that accept Stick-On modules and provide easy access for configuration and changes.
The ST-VP2 Automatic Ducking Module is a device designed to cut out music when a page is played over your audio system and automatically fade the music back into play when the page is finished. Use of the unit requires a line-level music source from a receiver, satellite decoder, tape, or CD source.
25m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
20m U-Flex Slim Armored HDMI 2.1 8K@60HZ
The STA-2A Dual High-Gain Line Amplifier is a dual-channel line-level audio preamplifer. This unit offers up to 24dB gain in audio lines. Conversion between balanced and unbalanced audio is possible, as is conversion between high and low impedance.
The EZ-MX4L is a stereo audio mixer with four line inputs. All line inputs connect through RCA jacks; one also includes a MINI-jack input. Left and right channel LED VU metering facilitates easy level adjustment. The line output is available on stereo RCA jacks or on a MINI-jack. Includes worldwide power supply (specify plug).
The RU-SH1 is a dual-channel headphone amplifier with balanced/unbalanced left and right inputs accepting operating levels between -20 dBV and +20 dBu. Two recessed slide switches located on the side of the rear enclosure are set prior to mounting the module: one sets the input sensitivity, the other selects between stereo and mono operation.
30m USBC - HDMI 2.0 AOC - Video only
30m Cat.6A U/FTP RJ45/RJ45 Armor U-Flex
The RU-VA2 is the optimum choice where connectorized, rack-mounted video attenuation is needed. This unit features two separate, passive isolated channels. A single input jack is provided for each attenuator. The output jack is intended to be connected to a 75 Ohm terminated load. A front-panel knob is provided to adjust hot video levels down to the...
Speaker cable ZNK 8/14 (8x2.5 mm2) black. Assembled with NL8FC on both sides.
Bantam Cable, Swissflex, 2 x 2 x 0.19 mm2, outer diameter 2 x 4 mm, spiral shield, black, halogen free, adjustment: K/HS
Techflex F6 Woven, diameter, 25.4mm, white, 30.5m
61m Techflex FlexoPET, diameter 25.4-54mm, white
61m Techflex FlexoPET, diameter 25.4-54mm, beige
61m Techflex FlexoPET, diameter 25.4-54mm, grey
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3FXX.
The ST-UBA2 Unbalanced to Balanced Amplifier is used in any application requiring conversion from unbalanced consumer format signals to professional +4 dBu. It may be used to balance audio from CD players, cassette decks, computer sound cards, televisions, and a wide variety of other unbalanced sources. The mono sum output may be used to drive patch-bay...
NO2M4DW-FX-BOLC-0.5
Pull-In-Cable AOC 2.0 4K60Hz 30m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 25m
The EZ-SX4 is a stereo audio source selector with an output volume control that adjusts the line-level output. This unit is ideal as a four input source selector feeding an associated audio amplifier. The user can conveniently select an audio source and adjust the level on the front panel. Includes worldwide power supply (specify plug).
25m Armored AOC HDMI 2.0 4K Cable UF
152.4m Techflex FlexoPET, diameter 6.4-19.1mm, grey
152.4m Flexo PET braided sleeve, diameter 12.7mm, orange
152.4m Techflex FlexoPET, diameter 6.4-19.1mm, white
152.4m Techflex FlexoPET, diameter 6.4-19.1mm, black
152.4m Techflex FlexoPET, diameter 6.4-19.1mm, beige
NO2M4DW-FX-BOLC-0.2
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3MXX.
76.2m Techflex FlexoPET, diameter 19.1-44.5mm, black
76.2m Techflex FlexoPET, diameter 19.1-44.5mm, grey
76.2m Techflex FlexoPET, diameter 19.1-44.5mm, white
76.2m Techflex FlexoPET, diameter 19.1-44.5mm, beige
Power multicore cable CKPE50-ASAS-M300
The EZ-HDA4B contains four stereo headphone amplifiers with individual front-panel volume controls. Headphone outputs are provided on rear-panel MINI jacks. One stereo input signal feeds all the amplifiers. Stereo RCA jacks, a MINI jack and a 1/4" jack are provided for connecting the input source. Includes worldwide power supply (specify plug).
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Tascam standard.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Yamaha standard.
80m 12G / 2 x UHD BNC / Cable CPR: Dca
Techflex Flexo F6 Diameter 19.1mm WT 30.5m
Techflex Flexo F6 Diameter 19.1mm GR 30.5m
Interface cable ZNKMP8/14 (Multicore analog 11.7 mm, 8 x 2 strands 0.22 mm2, PVC-coating black), D-Sub 25 pole male to D-Sub 25 pole male.
Techflex Flexo Wrap, diameter 63.5mm, black, 10m
The FP-PA20A features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted either manually or with a trimming screwdriver. The gain range will accommodate standard unbalanced levels as well as professional balanced levels. Both a 70 V and 100 V amplified output are provided to drive...
40m 0.8L/3.7 Flex 6GHz, KTGT310 2xUHDBNC
The STA-1 is a high quality, miniature wall and surface mount, dual-channel audio electronic line transformer and amplifier, designed for use in situations where balanced/unbalanced configuration conversion and level boost are required.
The FP-SPR1 SPDIF Repeater & Amplifier is single-channel module designed to perform conversion between SPDIF connector types and recovery of low SPDIF signal levels. It features an input and output for each conventional SPDIF format: BNC, phono, and optical. Only one of the three outputs or a combination of the coaxial and optical outputs may be used...
Power Turtle XO CPTM-S1-T6
The RDL Active D-Series Loudspeaker features a gray grill and is designed to deliver rich, detailed sound while in Decora-compatible wall or chassis mounts. The input accepts either a -10 dBV unbalanced or a +4 dBu balanced signal on the rear-panel detachable terminal block.
The RDL Active Loudspeaker Format-A Series features a grey grill and is designed to deliver rich, detailed sound while in Decora-style compatible wall or chassis mounts. The loudspeaker is a single-pair audio amplifier module compatible with RDL Format-A twisted pair products.
The EZ-MPA1 is a microphone preamplifier with front-panel volume control and audio level metering. A front-panel switch engages an audio compressor to control overloads and clipping during high level audio bursts or peaks from the microphone. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. Includes worldwide...
The DB-TPR3A Active Triple Pair XLR and RCA Stereo Audio Output over RJ45 Receiver Module is a three-pair audio receiving module compatible with RDL Format-A twisted pair products. The DB-TPR3A features a black front-panel laminate. The DB-TPR3A module features an XLR audio output and two RCA phono jack outputs, one for the left channel and one for the...
Field Assembly SLC
The ST-CL2 is a miniature wall and surface mount, high performance compressor/limiter from RDL, designed to maintain a constant average output level and effective peak control over a wide range of input levels. The input and output are line level and each may be wired balanced or unbalanced.
The FP-PA20 features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted either manually or with a trimming screwdriver. The gain range will accommodate standard unbalanced levels as well as professional balanced levels. The output will drive an 8 Ohm speaker or multiple speakers connected to...
Interface cable ZNKMP8/14 (Multicore analog 11.7 mm, 8 x 2 strands 0.22 mm2, PVC-coating black), D-Sub 25 pole male to D-Sub 25 pole male.
Enhanced inspection and cleaning procedure. Lockable with opticalCON MTP cable connector. Compatible with conventional cleaning and inspection equipment
XP Opt. Chassis Con M
20m Cat.6AU/FTP ECON Armor UFlex GT235
20m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
Techflex Flexo F6, diameter 31.8mm, gray, 15m
20m U-Flex Armor HDMI 2.1 8K@60HZ
The STM-2 is a quality low-noise microphone preamplifier designed for use in commercial sound, broadcast, and recording. The STM-2 is very flexible, with gain adjustment from 35 to 65 dB, two balanced or unbalanced outputs, and available phantom supply input. Its ultra-low distortion and lownoise performance make it the best choice, even when larger...
The FP-PA20B features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted either manually or with a trimming screwdriver. The gain range will accommodate standard unbalanced levels as well as professional balanced levels. A 25 V amplified output is provided to drive corresponding speakers in...
Techflex F6 Woven Diameter 6.4mm BL 61m
15m U-Flex Slim Armored HDMI 2.1 8K@60HZ
Techflex F6 Woven, diameter 38.1mm, white, 15.2m
The TX-TPR3A is a three-pair audio receiving module compatible with RDL Format-A twisted pair products. Three outputs are provided corresponding to the three signal pairs A, B and C. The audio signal received on each pair of the RJ45 INPUT jack feeds the corresponding -10 dBV unbalanced RCA phono jack output and the +4 dBu balanced detachable terminal...
The TX-TPS3A is a three-pair active sending module compatible with RDL Format A twisted pair products. Balanced and unbalanced inputs with studio-quality buffer amplifiers feed the RJ45 output. Local power can be provided 24VDC via twisted pair cable, terminal block or power jack while modules connected to the RJ45 output receive power as well.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3FXX.
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3FXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
ZNKMP8/14 (Multicore cable 11,7 mm 8 x 2 strands of 0,22 mm2 with PVC jacket) Side a: 8 x NC3FXX; Side b: 8 x NC3MXX incl. XXCR and coloured BXX
Car Hifi, Line, RCA Stereo-Cable, 20cm (INPUT RCA female / female, OUTPUT RCA male / male) 1:1 transmission for 600 Ohm impedance, stereo Line up to 6V frequency response of 30Hz-40KHz. Transmission with ground lift 1:1 (NTL1), no ground loops and annoyances anymore.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NP3X.
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 4 x NC3FXX / 4 x NC3MXX; side b: 4 x NC3MXX / 4 x NC3FXX. inkl. XXCR and coloured boots BXX (brown, red, orange and yellow).
Pull-In-Cable AOC 2.0 4K60Hz 25m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 25m
The TX-VCR is the ideal choice in installations where a control signal is needed based on the absence or presence of valid video signals. The unique power supply input allows the TX-VCR to be powered from a wide variety of existing ac or dc power sources
Interface cable ZNKMP8/14 (Multicore analog 11.7 mm, 8 x 2 strands 0.22 mm2, PVC-coating black), D-Sub 25 pole male to D-Sub 25 pole male.
Speaker cable with FRNC jacket, 2 x 1.5 mm2, outer diameter 6.2 ± 0.4 mm, flame-retardant according to IEC 60332-1, CPR: Eca, wire insulation PEE.
9m ZNKMP8/14 Multicore cable 11.7 mm, 8x2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3MXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
The FP-TPS4A is an RDL Format-A Audio Sender that accepts either a stereo line-level or 1 to 3 Watt mono amplified fixed-level signal, usually from a commercial hospitality equipped TV. The FP TPS4A distributes the source signal to two Format-A output jacks to feed multiple Format-A receivers.
The ST-DA3 distribution amplifier is part of the "Stick-On" series and includes durable adhesives for permanent or detachable mounting. The ST-DA3 allows bridging of any audio line, gain adjustment, and signal distribution to three balanced or unbalanced outputs.
The Radio Design D-SH1M is a surface mounted, stereo / mono, headphone amplifier for audio installations of any kind. Museum exhibits, private audio monitoring installations, and listening stations are among some of the possible applications the D-SH1M is suitable for. The module mounts conveniently in a precut opening in a wood or metal enclosure or in...
Techflex Flexo F6 Diameter 12.7mm WT 45.7m
Techflex Flexo F6 Diameter 12.7mm GR 45.7m
75m 12G / 2 x UHD BNC / Cable CPR: Dca
ZNK CT2956401BL Multicore cable 14.9 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NP3X, side b: 8 x NP3X incl. PXR and coloured BPX.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3MXX.
Interface cable ZNKMP8/14 (Multicore analog 11.7 mm, 8 x 2 strands 0.22 mm2, PVC-coating black), D-Sub 25 pole male to D-Sub 25 pole male.
20m Cat.6AU/FTP RJ45 Armor UFlex GT235
ANTENNA CABLE RG142BU SMA 4.5M
Techflex F6 Woven Diameter 4.8mm BL 61m
?1×2 HDMI Splitter, Repeater, & HDMI/ARC Audio Extractor
The DB-TPR2A Active RCA Stereo Audio Output over Dual RJ45 Receiver Module is a CAT5 to RCA phono receiver module. The The DB-TPR2A features a black front-panel laminate. The DB-TPR2A module features two RCA phono jack outputs, one for the left channel output and one for the right channel.
12.5m U-Flex Slim Armor HDMI 2.1 8K@60HZ
ANTENNA CABLE S04162B SMA 15M
The STM-DA3 is designed for use in quality commercial sound, broadcast and recording applications. The 1.2 kilohm balanced input accepts a wide variety of microphone input levels without loading professional low impedance microphones. A multi-turn trimmer is user adjustable for either gain or loss in order to match the facility standard microphone levels.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Tascam standard.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Yamaha standard.
The ST-MX2 is used in any application requiring mixing of two audio sources. A mic may be mixed with a line-level music source. Two mics may be mixed to feed the mic or line level input of a power amplifier. A mic or professional +4 dBu line-level mono sum is possible. It may be used to convert mono line-level signals from consumer to professional, or...
The ST-VP1 Voice-Over & Paging Module is a device that allows you to do voice-over paging with controls for fade and cut. It allows you to choose between (2) input audio sources. The unit is also well suited for voice-overs that require precise and consistent fade levels. This model can be configured for automatic operation when used in conjunction...
20m U-Flex Slim Armored HDMI 2.0 4K@60HZ
Crimp tool die for HX-R-BNC. Pin crimping: 1.80 mm. Shield and jacket: HEX 10.00 mm (A)
The EZ-ADA4 is a stereo audio distribution amplifier with gain adjustment and audio level metering. The input is connected through RCA jacks or a MINI jack. A front-panel knob adjusts for high or low input levels using the left and right channel LED VU meters. Four stereo outputs are provided on RCA jacks.
The ST-PH1 Stereo or Mono Phono (Turntable) Preamplifier features a compact, stick-on design ideal for commercial audio installations. The ST-PH1 will accept mono or stereo phono signals and is capable of balanced or unbalanced output. There are screw terminal connections.
This universal positioner is a crimping die for SVKTCRIMP-versions.
Coax cable stripper for cable O.D. ?8.0 mm for Neutrik rearTWIST BNC NBLC75BSX14 connector assemblies.
The ST-UMX3 Stick-On series miniature audio mixer features 3 input channels with switchable microphone or line level input level. The ST-UMX3 is an ideal solution for fixed installation in commercial offices, retail stores, schools, medical offices and general sound reinforcement applications. The 3 inputs are summed to a single output that is also...
Techflex CleanCut, diameter 19.1-30.2mm, black, 76.2m
Techflex CleanCut, diameter 19.1-30.2mm, gray, 76.2m
Black, balanced microphone cable, 2 x 0,22 mm2, with FRNC jacket, compliance: CE, EN 50575:2014+A1:2016, CPR: Dca, with double spiral shield and Visco wires, with an outer diameter of 5.8 mm.
The RC-1UR is a 1RU utility chassis for mounting RDL modules and accessories. The front and rear each feature three RACK-UP mounting bays. The mounting bays fit RACK-UP series products and AMS accessories (using AMS-HR4 adapters, available separately). The interior provides space to mount various STICK-ON and TX series modules.
The DB-SFRC8L Audio Selector is a SourceFlex module for wall mounting in a room, providing source selection from up to 8 audio sources. A numeric display shows the selected source. There are two line-level audio outputs on the rear of the unit, balanced and unbalanced, to feed an external power amplifier. The balanced line output level is +4dBu nominal...
The EZ-VDA3B is a composite video distribution amplifier with three outputs. The input and outputs are all 75 Ohm on BNC connectors. If the outputs are connected to long coaxial cables (typically 100 to 1000 feet) the front-panel gain and equalization trimmers may be adjusted to restore picture clarity. Includes worldwide power supply (specify plug).
The TX-PCR1 Paging Controlled Relay is ideal for local speaker muting during an area page and can be used for controlled switching of constant-voltage audio sources. The detachable terminal block has inputs for 25, 70, or 100V systems. The Slave output can be used to control other modules or the DPDT relay can switch speaker loads.
Techflex F6 Woven, diameter 25.4mm, black, 30.5m
Active Two-Pair Sender. Twisted Pair Format-A. XLR Microphone & Stereo RCA In. The -TPSL2A modules are two-pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources.
The DB-TPS3A Triple Pair RJ45 Sender Module is a three-pair audio sending module compatible with RDL Format-A twisted pair products. The DB-TPS3A features a black front-panel laminate. This module features an XLR microphone input and two RCA phono jack inputs, one for the left channel source and one for the right channel source.
15m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3FXX.
White, unequipped connection box made of powder-coated sheet steel for wall mounting, with 4x FLF cut-outs, 6x D-series cut-outs and rear cable inlet. Dimensions: 111 x 95 x 207 mm.
Speaker cable ZNK 8/14 (8x2.5 mm2) black. Assembled with NL8FC on both sides.
70m 12G / 2 x UHD BNC / Cable CPR: Dca
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3FXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
ZNKMP8/14 (Multicore cable 11,7 mm 8 x 2 strands of 0,22 mm2 with PVC jacket) Side a: 8 x NC3FXX; Side b: 8 x NC3MXX incl. XXCR and coloured BXX
The STR-19A Stick-On Series Racking System (12 Modules) is a mounting kit designed to accommodate (12) RDL Stick-On modules. It can be mounted in a rack or secured to almost any flat surface. The unit features a series of specially designed slots that accept Stick-On modules.
10m U-Flex Slim Armored HDMI 2.1 8K@60HZ
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NP3X.
The DB-TPR1A Active Single Pair RJ45 Receiver Module is a single-pair audio receiving module compatible with RDL Format-A twisted pair products. The DB-TPR1A features a black front-panel laminate. This unit features an XLR output jack. A rear-panel switch set during installation determines which of the three Format-A pairs is buffered to feed the module...
Black 19 inch desk drawer or tray (mounted upside down) made of steel, 1 RU, with lateral handles, without full pull-out.
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 4 x NC3FXX / 4 x NC3MXX; side b: 4 x NC3MXX / 4 x NC3FXX. inkl. XXCR and coloured boots BXX (brown, red, orange and yellow).
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 7.36 mm (A), 5.0 mm (B)
Pull-In-Cable AOC 2.0 4K60Hz 20m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 20m
Techflex Flexo F6 Diameter 9.5mm WT 45.7m
Techflex Flexo F6 Diameter 9.5mm GR 45.7m
The DB-TPS1A Single Pair RJ45 Sender Module is a single-pair audio sending module compatible with RDL Format-A twisted pair products. The DB-TPS1A features a black front-panel laminate. The DB-TPS1A module features an XLR microphone input. The module provides IEC 24 V phantom and accepts input signals from both dynamic and condenser microphones.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3MXX.
Active Single-Pair Sender. Twisted Pair Format-A. Mini-Jack & Stereo RCA In. The -TPSL1A modules are single pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources.
15m U-Flex Armored HDMI 2.1 8K@60HZ
The ST-IC1 is a professional-quality compact intercom amplifier ideal for situations where an intercom system is going to be installed, or where an amplifier is needed to increase a mic level signal up to a 1W speaker level.
304.9m Flexo PET braided sleeve, diameter 6.4mm, orange
25m Cat.6A U/FTP RJ45/RJ45 Armor U-Flex
The EZ-PA20 is a stereo audio amplifier with one line input and a front-panel volume control. An integral compressor/limiter allows a higher sound output level without clipping than is possible using a standard amplifier. The output drives 4 or 8 ohm speakers. Includes worldwide power supply (specify plug).
The ST-GSP1 is a miniature wall and surface mount gated speech preamplifier, designed to be used in a variety of situations where it is desired to produce an automatically switched line-level signal from a microphone.
6m ZNKMP8/14 Multicore cable 11.7 mm, 8x2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3MXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
The -TPA1A modules are two pair audio amplifier modules compatible with RDL Format A twisted pair products. Each -TPA1A receives stereo audio and 24 Vdc power through a rear-panel RJ45 jack. The left and right audio signals received on pairs B and C of the twisted pair cable are summed to mono and amplified.
ZNK CT2956401BL Multicore cable 14.9 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NP3X, side b: 8 x NP3X incl. PXR and coloured BPX.
The ST-NG1 is the ideal choice where random white or pink noise is needed. It is suitable either as a reference noise source for audio measurements or as a masking noise source in engineered sound or counter-intelligence applications.
Enhanced inspection and cleaning procedure. Lockable with opticalCON DUO cable connector. Compatible with conventional cleaning and inspection equipment
Enhanced inspection and cleaning procedure. Lockable with opticalCON QUAD cable connector. Compatible with conventional cleaning and inspection equipment
FF EBC15 foxBRID Chassis coup 2CH MM OM4
Power multicore cable CKPE50-ASAS-M200
25m USBC - HDMI 2.0 AOC - Video only
Assembled Coaxial Cable RF RG213 B/U MIL C17 F (ZNK CK2775400), black, overall-diameter 10.3 mm (Attu @ 100MHz/100 m = 6.4dB), with 2 x NBNC-RG213, male 50 Ohm, black boots.
15m Armored AOC HDMI 2.0 4K Cable UF
12.5m 2.1AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
7.5m U-Flex Slim Armor HDMI 2.1 8K@60HZ
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Yamaha standard.
Digital cable ZNK CT2956401-BL (digital multicore AES / EBU), 14.9 mm, with 8x 2 wires 0.22 mm2, in black PVC jacket, with 25-pin D-Sub connector to 4x 3-pin XLR -Cable connector NC3MXX-BAG and 4x 3-pin XLR cable sockets NC3FXX-BAG, assigned according to the Tascam standard.
Pull-In-Cable AOC 2.0 4K60Hz 17.5m
Pull-In-Cable, AOC, 2.1 8K60Hz CPR 17.5m
The ST-GCA3 Auto Gain Control Amplifier constantly adjusts audio levels so you always maintain the correct output. The adjustment rate is switch-selectable so you get an even greater amount of control. The SLOW mode works best at leveling music sources, while the FAST mode is ideal for changing conditions that require instant adjustments.
12.5m U-Flex Armored HDMI 2.1 8K@60HZ
HDBT-Ext-RX, HDMI1.4 ,RS232, IR, 70m@1080p
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3FXX.
76.2m Techflex FlexoPET, diameter 15.9-41.3mm, beige
76.2m Techflex FlexoPET, diameter 15.9-41.3mm, black
76.2m Techflex FlexoPET, diameter 15.9-41.3mm, grey
76.2m Techflex FlexoPET, diameter 15.9-41.3mm, white
61m Techflex FlexoPET, diameter 25.4-54mm, black
The ST-SH2 is a miniature wall and surface mount stereo headphone amplifier. The unit is used for installation applications requiring headphones of any impedance to be driven from consumer or professional audio sources.
The DB-TPS2A Active Dual Pair RJ45 Sender Module is a two-pair audio sending module compatible with RDL Format-A twisted pair products. The DB-TPS2A features a black front-panel laminate. The DB-TPS2A module features two RCA phono jack inputs, one for the left channel source and one for the right channel source. These inputs are designed to receive...
The TX-TPR1A Active Single-Pair Receiver is compatible with Format A twisted pair products. The line-level receiver has an RJ-45 input which feeds -10 dBV unbalanced RCA phono jack output or the +4 dBu balanced detachable terminal block output. Power can be provided from 24VDC power supply to the power jack or the detachable terminal block.
The ST-MX3 is a line-level mixer module in the Stick-On Series of products. It provides audio mixing of three line-level inputs with individual input gain adjustments. The line-level output is capable of driving either high or low impedance, balanced or unbalanced loads.
Car Hifi AUX Input 3.5 mm stereo plug, output 2x RCA male 1:4 transfer of a signal with 200 Ohm impedance, stereo line up to 1.2V, frequency response 30Hz-40KHz. Signal transmission 1:4 (NTM4) with separated earth, prevents interferences and hum loops. Particularly suited to connecting external sources with earphone jacks to an AUX input (audio radio)...
The ST-PA18 is a high-quality compact audio power amplifier designed for use with an eight Ohm speaker system. It offers 18W of RMS power. It features screw terminal connectors, and can accept balanced or unbalanced input signals. A loop output is also provided for connecting additional amplifiers.
Techflex F6 Woven, diameter 38.1mm, black, 15.2m
The TX-TPS1A is an active single pair sender for use with RDL's Format A twisted pair cable. A single line level source can be connected via balanced or unbalanced input with a studio-quality buffer feeding the RJ45 output. The loop in RJ45 jack can be used to accept signal from other Format A senders. Three seperate single pair senders can be routed with...
The ST-LCR3 Logic-Controlled Relay (Dual Alternate Pulse) is a device designed for use in installations where momentary pulses are needed from a single control signal. This module provides a momentary pulse when a logic signal on its input initially becomes active. A separate momentary pulse is provided when the input becomes inactive.
This cable reel is made of sheet steel, has a core diameter of 178 mm and no cover. It is suitable for daily outdoor applications and is equipped with exchangeable, shock-resistant steel panels. An ergonomic fixing brake is integrated in the frame.
Power Turtle XO CPTM-H1-T6
65m 12G / 2 x UHD BNC / Cable CPR: Dca
The STR-H6A 10.4" Rack Adapter allows you to securely rack mount up to 6 STICK-ON modules. This adapter fits 10.4" (26.41 cm) racks.
Crimp tool die for HX-R-BNC. Pin crimping: HEX 1.75 mm. Shield and jacket: HEX 9.73 mm (A)
Flap with auxiliary coil ZU GT 450, SK 450
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NC3MXX.
Y-speaker cable with one 8-pole speakON NLT8MX-BAG to 4x 4-pole speakON NLT4MX-BAG, 2-pole wired.
The ST-MPA48 contains two identical phantom power circuits and a common power supply input. If only one mic input is to be converted for phantom operation, only one circuit needs to be used. Each circuit has a mic input and a mic output. Phantom voltage appears on each of the mic input terminals. Therefore, the ST-MPA48 can convert any existing mic input...
ZNKMP8/14 (Multicore cable 11,7 mm 8 x 2 strands of 0,22 mm2 with PVC jacket) Side a: 8 x NC3FXX; Side b: 8 x NC3MXX incl. XXCR and coloured BXX
The RK-2U 19" 2U Utility Rack Chassis is a portable and versatile equipment rack that can be placed on or mounted to any flat surface. It has a rack height of 2U and accommodates standard 19" equipment. This solution is ideal for RDL modules or any other equipment that requires a flexible lightweight racking solution.
9m (Tascam) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
9m (Tascam-Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
9m (Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
Power multicore cable CKPH50-AHAH-M400
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3FXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NP3X.
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 4 x NC3FXX / 4 x NC3MXX; side b: 4 x NC3MXX / 4 x NC3FXX. inkl. XXCR and coloured boots BXX (brown, red, orange and yellow).
3-fold crimp die (HEX 1.09/3.38/4.75) for coaxial cables with following dimensions: 0.6/2.8-4.7 and RG-179B/U.
The ST-CX2 is a miniature wall and surface mount two-way crossover, designed to drive audio power amplifiers. The input and outputs are balanced, but may be connected unbalanced if necessary.
The ST-CX2S is a miniature wall and surface mount subwoofercrossover, designed to drive audio power amplifiers. The input features two separate isolated balanced-bridging inputs, each of which can be wired balanced or unbalanced.
Techflex Flexo F6 Diameter 19.1mm BL 30.5m
The ST-HP3 is a miniature wall and surface mount dual high-pass filter, and is the ideal choice where line-level audio filtering needs to be provided at the input of a power amplifier for protection of public address horns against damage from low frequencies.
5m U-Flex Slim Armored HDMI 2.1 8K@60HZ
Pull-In-Cable AOC 2.0 4K60Hz 15m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 15m
Coaxial Multi Channel Cable (755-1103 type), overall foil screened, outer diameter 10.3 mm, black, (Attu. @ 100MHz/100 m = 17.9dB), high resolution cable, high flexible cable, assembled on both side with 1x D-Sub 15 pole male, shell all metal, gold-plated contacts.
LS Cable 2x1.5 mm2, Diameter 6mm White, 100M
10m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
20m USBC - HDMI 2.0 AOC - Video only
The ST-GLA1 Gated Line Amplifier & Noise Gate is a device that allows you to produce an automatically switched line-level signal with integral noise reduction. The unit can be used as a stand-alone solution or combined with other RDL modules to produce a custom mixing system. It features an open-collector slave output that can be used to trigger other...
The ST-VCA3 Voltage-Controlled Amplifier provides smooth audio-level control from a remote control panel, allowing you to adjust voltage from 0 to 10VDC. Use this unit when you need to keep audio sources and components isolated in rack, but want to extend audio controls outside of the rack and eliminate scratchy audio.
Illuminated Touch-Activated Pushbutton
The black DB-SH1 Stereo Headphone Amplifier - Decora Panel with User Level Control is used in applications requiring headphones of any impedance to be driven from consumer or professional audio sources. The DB-SH1 is ideally suited to applications as diverse as language translation, museums, interview studios and music stores.
3m ZNKMP8/14 Multicore cable 11.7 mm, 8x2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3MXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
Green single Mode APC. The opticalCON Transceiver Adapter connects an opticalCON chassis (NO2-4FDW*) and a LC SFP transceiver. NAO2*-SFP-LC consists of two LC-SFP adapters, 2 flat gaskets (1mm and 2mm) and one NO2-4FDW-A without copper contacts.
Assembled Coaxial Cable RF RG213 B/U MIL C17 F (ZNK CK2775400), black, overall-diameter 10.3 mm (Attu @ 100MHz/100 m = 6.4dB), with 2 x NBNC-RG213, male 50 Ohm, black boots.
ZNK CT2956401BL Multicore cable 14.9 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NP3X, side b: 8 x NP3X incl. PXR and coloured BPX.
Techflex CleanCut, diameter 15.9-25.4mm, black, 76.2m
Techflex CleanCut, diameter 15.9-25.4mm, gray, 76.2m
Bantam Cable, Swissflex, 4 x 0.22 mm2 + spiral shield, outer diameter 4.7 mm
Microphone cable Kevlar AES/EBU,PVC INDOOR,100M
2/1 Shrinkfl. U-Clear, Diameter 12.7mm Bulk 76.2m
20m Cat.6A U/FTP ECON/ECON Armor U-Flex
10m U-Flex Armored HDMI 2.1 8K@60HZ
12.5m Armored AOC HDMI 2.0 4K Cable UF
Techflex F6 Woven diameter 19.1mm WT 30.5m
The preassembled etherCON CAT6 patch cables use a shielded S/FTP cable with cable plug carrier offering a robust metal shell and Push-Pull locking system.
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NP3X.
Black microphone cable with 2 x 0.22 mm2, double spiral shield and Visco wires, PVC jacket and with an outer diameter of 6 mm.
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 5.41 mm (B)
The black DB-SH1M Stereo Headphone Amplifier made is a dual channel headphone amplifier with balanced/unbalanced left and right inputs. Each input accepts operating levels between -20 dBV and +20 dBu. Prior to mounting the module, there are two recessed switches on the rear enclosure that are set up. One switch is for setting the input sensitivity and the...
Bantam Cable, Swissflex, 2 x 2 x 0.19 mm2, outer diameter 2 x 4 mm, spiral shield, black.
Pull-In-Cable, AOC, 2.1 8K60Hz CPR 12.5m
Pull-In-Cable AOC 2.0 4K60Hz 12.5m
3m U-Flex Slim Armored HDMI 2.1 8K@60HZ
Black, dual Siam instrument cable, 2 x 1 x 0.22 mm2, with spiral shield, PVC jacket and an outer diameter of 2 x 4 mm.
ZNKMP8/14 (Multicore cable 11,7 mm 8 x 2 strands of 0,22 mm2 with PVC jacket) Side a: 8 x NC3FXX; Side b: 8 x NC3MXX incl. XXCR and coloured BXX
D-Sub Multicore cable analog, ZNKMP8/14 (Multicore cable analog 11.7 mm, 8 x 2 strands of 0.22 mm2 PVC-coating black), D-Sub 25 pol. male to 8 x NP3X.
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3FXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
CONTRIK Power Strip XO CCV5RD-6T1-2C
Die for Crimp XLR XX-HA. Suitable for tool HX-R-BNC. Standard B-crimp acc. to IEC 60352-2. Wire size AWG 24-22, 0.22 - 0.34 mm2
ZNKMP8/14 Multicore cable 11.7 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 4 x NC3FXX / 4 x NC3MXX; side b: 4 x NC3MXX / 4 x NC3FXX. inkl. XXCR and coloured boots BXX (brown, red, orange and yellow).
60m 12G / 2 x UHD BNC / Cable CPR: Dca
Coax cable stripper for cable O.D. ?8.0 mm for Neutrik rearTWIST BNC NBLC75BVZ17 connector assemblies.
7.5m 2.1 AOC 8K@60Hz/4k@120Hz,48Gbps,CPR
Crimp tool, frame. ATTENTION: Suitable dies are DIE-R-* and DIE-R-BNC*
Blue single Mode PC. The opticalCON Transceiver Adapter connects an opticalCON chassis (NO2-4FDW*) and a LC SFP transceiver. NAO2*-SFP-LC consists of two LC-SFP adapters, 2 flat gaskets (1mm and 2mm) and one NO2-4FDW-A without copper contacts.
Techflex F6 Woven Diameter 9.5mm WT 30.5m
The black DB-TPS8A Active Two-Pair Sender is a two-pair audio sending module compatible with RDL Format-A twisted pair products. This module is designed to be mounted in wall boxes, cabinets, or other enclosures that allow users to connect audio sources and features a black front-panel laminate.
10m U-Flex Slim Armored HDMI 2.0 4K@60HZ
2m U-Flex Slim Armored HDMI 2.1 8K@60HZ
15m USBC - HDMI 2.0 AOC - Video only
Y-speaker cable with one 8-pole speakON NLT8MX-BAG to 4x 4-pole speakON NLT4MX-BAG, 2-pole wired.
Techflex Flexo F6 Diameter 12.7mm BL 45.7m
Flexible Etherflex patchcable (ZNK CT1019067) Cat. 7, twisted pair, PUR-rubber-jacket (resistant, non-abrasive, non-corrosive, flame retardant), assembled with Cat. 6A RJ45 Hirose connectors, screened (NE8CAT6A-HRS) along with standard boots.
1m ZNKMP8/14 Multicore cable 11.7 mm, 8x2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NC3MXX, side b: 8 x NP3X incl. XXCR/PXR and coloured BXX/BPX.
ZNK CT2956401BL Multicore cable 14.9 mm, 8 x 2 strands, 0.22 mm2, PVC-coat. Side a: 8 x NP3X, side b: 8 x NP3X incl. PXR and coloured BPX.
6m (Tascam) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
6m (Tascam-Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
6m (Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
20m Cat.6A U/FTP ECON/RJ45 Armor U-Flex
The 1.25 mm DRY cleaner for opticalCON chassis connector cleaning (LC front surface dry cleaning possible) is included in the opticalCON Fiber Optic Cleaning kit (CAS-FOCD) and can be reordered with the part number FOCD-DC125.
The TX-PD8X is the ideal choice where power distribution from a current-limited switching power supply is needed. It is suitable for powering up to eight modules from a single power supply. The current limiting circuitry in many switching power supplies will cause the supply to shut down upon power-up when a high current capacitive load is connected.
The TP-HA1A Format-A Stereo Headphone Amplifier is designed to allow someone to listen to music via headphones over an RDL Format-A sender system. The amplifier features two RJ45 ports, either of which can receive both the power and the audio signal to the amplifier. The second RJ45 port can be used to connect additional headphone amplifiers or another...
Speaker cable ZNK 2962800 (4x4 mm2) black, speakON NL4FX on each side.
The FP-TP4PW 4 Output Power Inserter is a four output power inserter compatible with RDL twisted pair products. The RU-TP4PW is powered from a 24 VDC power supply using either the power jack or the detachable terminal block. Four dual-RJ45 jack sets are provided to connect remote twisted pair senders and receivers.
1m U-Flex Slim Armored HDMI 2.1 8K@60HZ
Speaker cable ZNK 4/11 (4x2.5 mm2) black, speakON NL4FX on each side.
Pull-In-Cable AOC 2.0 4K60Hz 10m
NX-HDMI-ADA-10-I8 - Pull-In-Cable, AOC, 2.1 8K 60Hz 10m
152.4m Flexo PET braided sleeve, diameter 9.5mm, orange
76.2m Techflex FlexoPET, diameter 12.7-31.8mm, beige
76.2m Techflex FlexoPET, diameter 12.7-31.8mm, black
76.2m Techflex FlexoPET, diameter 12.7-31.8mm, grey
76.2m Techflex FlexoPET, diameter 12.7-31.8mm, white
7.5m U-Flex Armored HDMI 2.1 8K@60HZ
The UC-2R is a tabletop utility chassis for mounting RDL modules and accessories. The front and rear each feature two RACK-UP mounting bays. The mounting bays fit RACK-UP series products and AMS accessories (using AMS-HR4 adapters, available separately). The interior provides space to mount various STICK-ON and TX series modules.
Gray Multimode PC. The opticalCON Transceiver Adapter connects an opticalCON chassis (NO2-4FDW*) and a LC SFP transceiver. NAO2*-SFP-LC consists of two LC-SFP adapters, 2 flat gaskets (1mm and 2mm) and one NO2-4FDW-A without copper contacts.
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 5.00 mm (B)
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 4.53 mm (B), 4.06 mm (C)
Crimp tool die for HX-R-BNC. Pin crimping: 1.07 mm. Shield and jacket: 6.47 mm (A), 5.00 mm (B), 4.53 mm (C)
2-fold crimp die (HEX 1.69/7.01) for coaxial cables with following dimensions: 1.0/4.6-6.7.
3-fold crimp die (HEX 1.09/1.38/6.48) for RG59B/U coaxial cables.
Black power rail made of anodised aluminium with 1 RU and with 6x NAC3FPX female chassis connectors. The black cable with one T23 male connector has 3 meters length. Max. current load up to 16 A, inner conductor: 3 x 1.5 mm2.
7.5m Armored AOC HDMI 2.0 4K Cable UF
Techflex Flexo F6 Diameter 9.5mm BL 45.7m
Extendible and lockable 19 inch desk drawer made of black steel, 1 RU, with full pull-out.
20.0m HDMI 2.0 Active Cable 18 GBPS
cPot cable F-F 25mm2 50m
The ST-LCR2 Logic-Controlled Relay (Latching) is a device that provides double-pole double-throw dry switching contacts and LED indicators for relay closure. This unit uses alternate-action switching and should be used in installations where momentary pulses must alternately toggle on-off switching contacts.
Crimp tool die for HX-R-BNC. Pin crimping: 1.07 mm. Shield and jacket: 6.47 mm (A), 7.36 mm (B)
Techflex Flexo F6 diameter 6.4mm BL 61m
The ST-RG1 is a digitally generated 0 to 10 volt Ramp Generator which provides the ideal interface for audio volume control from multiple points with the ST-VCA3. Any number of Up and Down buttons may be connected to the ST-RG1. Sufficient drive is provided from the ST-RG1 to control up to six ST-VCA3s.
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 7.36 mm (B)
Power multicore cable CKPE50-ASAS-M100
The STA-1M is a high quality, miniature wall and surface mount, mono-audio amplifier, designed for use in situations where balanced/unbalanced configuration conversion, impedance conversion, and level boost or cut are required.
The ST-LCR1H 8-Amp High-Power Logic-Controlled Relay is a device that provides 8-amp dry-switching relay contacts for high-power switching. These contacts are well suited for switching many 8 Ohm, 70.7V, or 100V speaker lines, although the module can be used with virtually any type of control signal.
The preassembled etherCON CAT6 patch cables use a shielded S/FTP cable with cable plug carrier offering a robust metal shell and Push-Pull locking system.
The GB6 Ground Bar from RDL is a small metal bar designed to ground equipment. It is constructed from alloy copper and can be used to mount up to (6) TS-1D suppressors. Use this unit to protect your equipment from electrostatic discharge, induced transient voltage, RF interference, and electromagnetic pulses.
55m 12G / 2 x UHD BNC / Cable CPR: Dca
The ST-SSR1 offers absolutely silent switching between two line-level audio input signals. It may also be used as a silent on/off switch for a single channel. The ST-SSR1 can be programmed by the user for either fast or soft switching. The unit is built into an extremely compact housing for installation almost anywhere.
The TS-1D is intended to protect audio input and output circuits from the effects of transients induced on the audio lines. Single or multiple units are typically mounted to good earth ground at the location that audio lines enter or exit an equipment rack. This protects wiring inside the rack against the effects of induced electrostatic discharge (ESD),...
RJ45 Three-Pair Combiner to Single-Pair Format-A Audio Input Sender
Pull-In-Cable AOC 2.0 4K60Hz 7.5m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 7.5m
10m USBC - HDMI 2.0 AOC - Video only
20m Cat.6A U/FTP RJ45/RJ45 Armor U-Flex
5m 2.1 AOC 8K@60Hz/4k@120Hz, 48Gbps, PVC
The TX-A2D Stereo Balanced to Unbalanced Signal Converter simply converts a stereo (or 2 mono) balanced audio signals from professional audio sources to unbalanced stereo for input in consumer audio gear. The TX-A2D features two removable euroblock input connectors and dual RCA outputs.
The STM-1 is a low-cost, high-quality miniature wall and surface mount microphone preamplifier, designed for use in commercial sound and broadcast applications. The compact size makes it ideal where a larger or heavier preamp cannot be used.
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 8.23 mm (B)
The ST-OSC2A is a miniature wall and surface mount dual audio oscillator from RDL. The module provides separate left and right audio signals for each of two frequencies - 1kHz and 10kHz, and is well suited to audio installations requiring reference tones for level calibration and frequency response checks
The ST-OSC2B is a miniature wall and surface mount dual audio oscillator. The module provides separate left and right audio signals for each of two frequencies - 100Hz and 400Hz, and may be used in conjunction with the ST-OSC2A to provide a complete set of frequency response test tones, or in systems where 400Hz is used as the reference frequency.
20m Techflex FlexoPET, diameter 38.1-88.9mm, black
The ST-RX2 is a one-in, two-out line-level routing switch and a part of the "Stick-On" line. Anywhere you need to send an audio signal to one of two destinations, the ST-RX2 is an ideal companion. It offers solid-state switching to route the signal to one of the balanced outputs with an off attenuation better than 80dB at all frequencies; no relays or...
5m U-Flex Armored HDMI 2.1 8K@60HZ
5m Armored AOC HDMI 2.0 4K Cable UF
2/1 Shrinkfl. U-Clear, Diameter 9.5mm Bulk 76.2m
Techflex Flexo F6 Woven diameter 79mm WT 30.5m
The ST-VOX1 is a compact voice-activated audio controlled relay in the "Stick-On" line of products. The ST-VOX1 can be triggered directly from an unbalanced microphone when used in intercom or talkback applications. In many of those applications, the microphone signal must be preamplified, making the ST-VOX1 an great partner to the STM-1 preamp.
Crimp tool die for HX-R-BNC. Pin crimping: 1.60 mm. Shield and jacket: HEX crimp 6.47 mm (A), 7.01 mm (B)
3m (Tascam) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
3m (Tascam-Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
3m (Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
The ST-TC1 is intended to be connected to an on-site telephone system switching unit KSU. It is not intended to be connected directly to a telephone CO line. Connections from the ST-TC1 go into the telephone switching unit as if the ST-TC1 was an incoming phone line.
CONTRIK Power Strip XO CCV5RD-6T1-C
3m 2.1 AOC 8K@60Hz/4k@120Hz, 48Gbps, PVC
Anthracite grey, unequipped connection box made of powder-coated sheet steel, elegant design, with 4x FLF cut-outs, rear cable inlet, strain relief, brush and 4x mounting holes as well as 4x rubber feet. Dimensions: 265 x 118 x 68 mm / RAL 7016.
Power multicore cable CKPH50-AHAH-M300
The ST-SX4 is a four-input, single-output audio switcher in RDL's "Stick-On" line of products. It will send any one of the four unbalanced audio signals to the unbalanced output, or all of the sources may be switched off. A single input terminal provides control of the unit.
Pull-In-Cable AOC 2.0 4K60Hz 5m
Pull-In-Cable, AOC, 2.1 8K60Hz, CPR 5m
2m 2.1 AOC 8K@60Hz/4k@120Hz, 48Gbps, PVC
The EZ-PH1 is a stereo phono preamplifier with front-panel volume trimmers and audio level metering. Stereo RCA jacks and a grounding screw are provided on the rear panel for connecting a turntable tone arm. The input is preamplified with RIAA equalization to feed the line output RCA jacks. Includes worldwide power supply (specify plug).
The stainless steel DS-RT2 Remote Control Selector is designed to turn on and off an audio or video source. Only one output terminal is needed for triggering, therefore a single shielded pair (3-conductor cable) is required for remote connection. For more complex switching networks, both outputs (ON and OFF) may be used.
The ST-ACR1M is an audio controlled relay and part of RDL's "Stick-On" series of equipment. It is designed for reliable operation and quick, easy installation. The ST-ACR1M is designed to switch mic-level signals. Two multi-turn trimmers are provided, one for audio input sensitivity, and one for delay control.
The RDL ST-ACR1 is an audio controlled relay and part of RDL's "Stick-On" series of equipment. It is designed for reliable operation and quick, easy installation. The ST-ACR1 is designed to switch line-level signals. Two multi-turn trimmers are provided, one for audio input sensitivity, and one for delay control.
3m U-Flex Armor HDMI 2.1 8K@60HZ
Techflex F6 Woven Diameter 9.5mm BL 30.5m
1m 2.1 AOC 8K@60Hz/4k@120Hz, 48Gbps, PVC
The TX-MVX is the ideal choice in installations where either a manual switch or an open-collector must switch video signals. Video A is normally connected to Common. When the TRIG terminal is pulled to ground, Video B is connected to Common and Video A is disconnected.
5m USBC - HDMI 2.0 AOC - Video only
50m 12G / 2 x UHD BNC / Cable CPR: Dca
The ST-ACR2 is an audio controlled relay and part of RDL's "Stick-On" series of equipment. It is designed for reliable operation and quick, easy installation. The ST-ACR2 is designed to switch line-level signals. Two multi-turn trimmers are provided, one for audio input sensitivity, and one for delay control.
Power multicore cable CKPE50-ASAS-M050
The AV-HK1X is a mono transformer isolation module for use with a balanced, low impedance source and either a low or high impedance load. Input and output connections are provided on XLR jacks with gold-plated contacts.
The TX-AT1S is part of the group of versatile Max-TX series products from Radio Design Labs. Max-TX modules are the large format members of the RDL TX family, featuring the superior engineering and components common to RDL products. The durable adhesives provided with the TX-AT1S permit permanent or removable mounting. The TX-AT1S may be rack or surface...
The RDL EZ-HK3 Audio / Video Hum Killer is a high-quality video transformer isolation module. It's designed specifically for use with unbalanced high impedance audio inputs and 75 ohm composite video. The device features both input and output connections on gold-plated RCA jacks.
The ST-EQ3 is a miniature wall and surface mount three-band equalizer that features a balanced bridging input, which may be connected unbalanced if desired. The output driver is 150 Ohm balanced, and is intended to drive unbalanced or balanced lines of 150 Ohm or higher impedance.
The TX-LC2 Unbalanced to Balanced Line Combiner is a device that allows you to perform isolated mixing on (2) unbalanced line-level audio sources and feed them to a balanced or unbalanced audio line. Output from this unit is a mono mix of the stereo signal and gain of the combined signals is adjustable from unity to 14dB.
150 Pins for cables with diameter 19-28mm. Female cable connectors without contacts.
150 Pins for cables with diameter 22-32 mm. Female cable connectors without contacts.
The ST-PA6 is a professional-quality audio power amplifier with a two inputs and a single eight Ohm output, which delivers 6W RMS to an eight Ohm speaker. All connections are made via screw terminals. Each of the inputs is a balanced bridge, with both inputs being actively mixed equally. Simple gain and bass EQ controls are provided.
The black 19 inch panel wall box with 4RU and a depth of 127 mm is ideal for the mounting of different panels. The lateral cut-out makes cable feeding convenient and easy. An internal ground terminal permits an appropriate grounding concept. Dimensions: 482.6 x 127 x 214
The preassembled etherCON CAT6 patch cables use a shielded S/FTP cable with cable plug carrier offering a robust metal shell and Push-Pull locking system.
Black DisplayPort 1.2 cable, with 2x DisplayPorts with latch locking and in industrial quality, with 360 degree EMC shielding.
1m (Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
1m (Tascam) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
1m (Tascam-Yamaha) Digital interface cable ZNK CT2956401-BL (Digital-Multicore AES/EBU), 14.9 mm, with 8x 2 strands at 0.22 mm2, black PVC jacket, with 25-pole D-Sub male connector to 25-pole D-Sub male connector, wired according to the Tascam pinout standard. Yamaha and Tascam are registered brands.
Speaker Cable, 2 x 1.5 mm2, outer diameter 6.2 ± 0.2 mm, high-flexible, black.
Techflex Flexo F6 Woven diameter 254mm WT 15.2
The EZ-VDA2B is a composite video distribution amplifier with two outputs. The input and outputs are all 75 Ohm on BNC connectors. If the outputs are connected to long coaxial cables (typically 100 to 1000 feet) the front-panel gain and equalization trimmers may be adjusted to restore picture clarity. Includes worldwide power supply (specify plug).
The EZ-PD3 Power Supply Distributor from RDL is used where power distribution from a current-limited switching power supply is needed. It is suitable for powering up to three EZ modules from a single power supply. Upon application of power, the EZ-PD3 ramps the voltage up, charging any load capacitance as quickly as possible, then switching full voltage...
15m Cat.6A U/FTP ECON/ECON Armor U-Flex
Black in-wall mounting set EDIZIOdue, equipped with one short DisplayPort and one USB breakout cable female/female of approx. 15 cm length and one cover frame made of plastic. The breakouts have screw termination.
Techflex CleanCut, diameter 4.8-15.9mm, black, 75m
Assembled Coaxial Cable RF RG213 B/U MIL C17 F (ZNK CK2775400), black, overall-diameter 10.3 mm (Attu @ 100MHz/100 m = 6.4dB), with 2 x NBNC-RG213, male 50 Ohm, black boots.
Flexible Etherflex patchcable (ZNK CT1019067) Cat. 7, twisted pair, PUR-rubber-jacket (resistant, non-abrasive, non-corrosive, flame retardant), assembled with Cat. 6A RJ45 Hirose connectors, screened (NE8CAT6A-HRS) along with standard boots.
The TX-AFC1F Audio Format Converter Bal-Unbal delivers wideband audio, ultra-low distortion, audio clarity and headroom common to studio equipment in a module suited to both studio and general-purpose audio installations. It is a single-channel (mono) module featuring a female XLR balanced input and phono jack unbalanced output.
Y-speaker cables with 1x 8-pole speakON NLT8MX-BAG to 2x 4-pole speakON NLT4MX-BAG connectors, 4-pole wired.
CONTRIK Power Turtle XO CPVT7RT
The TX-AFC1M Audio Format Converter Unbal-Bal is the ideal choice for applications requiring studio-quality transformer coupling between an unbalanced audio source and balanced equipment. This module is passive and does not add gain to the converted signal. The TX-AFC1M is a single channel (mono) module featuring a phono jack input and male XLR output.
Single mode PC 1 x 2 LC splitter to split a fiber signal (100 - 50/50). Splitter can be used with NZPFD-2.
The TTLan HDBaseT 5Play Cat.6A patch cable ensures first-class transmission quality over short and long distances - even with high-resolution 4K picture qualities.
The RDL EZ-HK2 Composite Video Hum Killer is a high-quality video transformer isolation module. It's designed specifically for use with 75 ohm composite video. The device features both input and output connections on gold-plated RCA jacks. Each input jack is electrically isolated from the case itself, as well as from the output ground.
The ZIGEN ZIG-PAX is a transmitter/receiver extender kit for long distance transmission of digital and or analog stereo audio over a single CAT X type cable. The ZIG-PAX can be used as a point-to-point solution or integrated with Matrix switching equipment to extend digital and or analog inputs or outputs to remote locations while maintaining high...
The TX-PSD1 Paging Sound Detector is ideal for switching sources from within a constant-voltage system. This module is triggered when the threshold is exceeded and can remain open for 3-25 seconds (user programmable).
Flexible patchcable (ZNK CT2672601) twisted pair, UC300 HS26 4P, Cat. 5e, black PUR rubber-jacket (resistant, non-abrasive, non-corrosive, flame retardant), assembled with RJ45 Hirose connectors, screened (NE8CAT6A-HRS) along with standard boots (BSHCAT5/6-L-*).
Power Strip XO CPVT6RD-M
The ST-MPA24 contains two identical phantom power circuits and a common power supply input. If only one mic input is to be converted for phantom operation, only one circuit needs to be used. Each circuit has a mic input and a mic output. Phantom voltage appears on each of the mic input terminals. There is no voltage on the mic output terminals.
The SF-RA1 rack mounts several SysFlex modules in fixed or mobile installations. Modules quickly snap into the SysFlex rack mount and each is firmly secured with a single screw. The racking system segregates network and power wiring from the audio and digital audio connectors.
The white DC-4W Desktop or Wall Mounted Chassis is designed to hold 1, 2, 3, or 4 Decora style units, including RDL remote controls and connector plates. Installation is facilitated using the included mounting plate, which allows the chassis to mount to a tabletop or a vertical surface such as a cabinet or wall.
1RU opticalCON panel frame
Techflex Flexo F6 Woven diameter 79mm BL 30.5m
Speaker cable ZNK 8/14 (8x2.5 mm2) black. Assembled with NL8FC on both sides.
The AV-HK1 is a stereo transformer isolation module for use with unbalanced, high impedance audio inputs. Input and output connections are provided on gold-plated phono jacks. The AV-HK1 is supplied with two adapter cables to facilitate connecting with products that use mini-plugs and jacks.
Service Tool for the opticalCON QUAD chassis connector NO4FDW-A
Speaker cable ZNK 4/11 (4x2.5 mm2) black, speakON NL4FX on each side.
Techflex F6 Woven Diameter 38.1mm WT 7.6m
15m Muco 4 x XLR f / 4 x XLR
Chassis connector with black chromium plating, 4 solder contacts and 1 LC-Duplex feedthrough socket, waterproof acc. to IP65, front panel mount
White in-wall mounting set EDIZIOdue, equipped with one short DisplayPort and one USB breakout cable female/female of approx. 15 cm length and one cover frame made of plastic. The breakouts have screw termination.
The TX-AT1 Audio Isolation Transformer is a single channel device that converts unbalanced audio to professional balanced audio. The TX-AT1 features binding-post connections and is an ideal choice for recording and sound reinforcement applications.
The TX-A2 Mono Balanced to Unbalanced Signal Converter simply converts a mono balanced audio signal from professional audio sources to unbalanced dual mono for input in consumer audio gear. The TX-A2 features a removable euroblock input connector and dual RCA outputs.
15m Cat.6A U/FTP ECON/RJ45 Armor U-Flex
Techflex Flexo PET diameter 508mm BL 15.2m
2/1 Shrinkfl. U-Clear, Diameter 7.9mm Bulk 76.2m
Black, 3-pole wired Draka DMX microphone cable (ZNK CT2963500) with Kevlar, PUR jacket and an outer diameter of 6.5 mm, assembled with 5-pole XLR male cable connector to 5-pole XLR female cable connector, both with silver-plated contacts. This cable is 3-pole wired: Pin 1 = Mass (shield); Pin 2 = Signal inverted (DMX?, Cold); Pin 3 = Signal (DMX+, Hot).
3m Y-speaker cable with one 8 pole speakON NLT8MX-BAG to 4 x speakON NL4FX 2 pole wired.
XP Opt. Chasis CON F
Black DisplayPort 1.2 cable, with 2x DisplayPorts with latch locking and in industrial quality, with 360 degree EMC shielding.
Type A, length 4, 40 IN (female/send) and 4 OUT (male/return)
Assembled Coaxial Cable RF RG213 B/U MIL C17 F (ZNK CK2775400), black, overall-diameter 10.3 mm (Attu @ 100MHz/100 m = 6.4dB), with 2 x NBNC-RG213, male 50 Ohm, black boots.
Combiner Line combines left and right channel of stereo signal by means of a passive network. afterwards the circuit is balanced by a NTL transformer (galvanic isolation) and terminated by a male XLR output. Especially used for stereo equipment with asymmetric outputs (RCA) for connections to a symmetric input (XLR female)
Distributes symmetrical mono output signal of a source to 2 RCA outputs+ (asym.) L + R. Via NTL1 (galvanic isolation) and a downstream passive network. Especially suited for transmission lines that should remain symmetric and be rendered asymmetric directly before arriving at the user (recipient).
Black power rail made of anodised aluminium with 1 RU and with 1x T13 female chassis connectors, 2x powerCON TRUE1 female chassis connectors (NAC3FPX) and 2x USB Chargers (5V/2A). An integrated thermal fuse serves as protection for the T13. The black cable with one T23 male connector has 3 meters length. Max. current load up to 16 A, inner conductor: 3 x...
The RDL EZ-HK1 Stereo Audio Hum Killer is a stereo audio transformer isolation module. It's designed specifically for use with unbalanced, high-impedance audio inputs. The device features both input and output connections on gold-plated RCA jacks. Each input jack is electrically isolated from the case itself, as well as from the output ground.
Speaker cable ZNK 2962800 (4x4 mm2) black, speakON NL4FX on each side.